| |
|
Mylar® EB11 is a low gloss polyester film with a matte surface. It is typically used as a carrier film. It is commercially available in nominal 48 - 300 gauge.
|
|
Mylar® EB11 is a low gloss, hazy product. Reverse side printing is superb, and metallized EB11 offers muted matte appearance. EB11 provides an excellent, low gloss surface texture transfer when used as a carrier film.
|
|
FDA Food Contact Status -
All gauges of Mylar® EB11 comply with the Food and Drug Administration regulation 21 CFR 177.1630 -- Polyethylene phthalate polymers, Sections (f), (g), and (h). This regulation describes films which may be safely used in contact with all types of food excluding alcoholic beverages. Uncoated films such as Mylar® EB11 can be used to contain foods during oven cooking or oven baking at temperatures above 250 °F.
|
| Available Thickness [Gauge] |
|
48; 92; 200; 300
|
|
|
| Property |
Thickness |
Value |
Units |
Test |
|
OPTICAL
|
| Gloss 60 Degrees |
48 |
34 |
% |
ASTM D2457 - 90 |
| Gloss 60 Degrees |
92 |
46 |
% |
ASTM D2457 - 90 |
| Gloss 60 Degrees |
200 |
55 |
% |
ASTM D2457 - 90 |
| Gloss 60 Degrees |
300 |
34 |
% |
ASTM D2457 - 90 |
| Haze |
48 |
73 |
% |
ASTM D1003 |
| Haze |
92 |
60 |
% |
ASTM D1003 |
| Haze |
200 |
73 |
% |
ASTM D1003 |
| Haze |
300 |
70 |
% |
ASTM D1003 |
| TLT |
48 |
80 |
% |
ASTM D1003 |
| TLT |
92 |
83 |
% |
ASTM D1003 |
| TLT |
200 |
81 |
% |
ASTM D1003 |
| TLT |
300 |
81 |
% |
ASTM D1003 |
|
|
|
PHYSICAL
|
| Elongation at Break MD |
48 |
102 |
% |
ASTM D882A |
| Elongation at Break MD |
92 |
144 |
% |
ASTM D882A |
| Elongation at Break MD |
200 |
188 |
% |
ASTM D882A |
| Elongation at Break MD |
300 |
175 |
% |
ASTM D882A |
| Tensile Strength MD |
48 |
19 |
kpsi |
ASTM D882A |
| Tensile Strength MD |
92 |
19 |
kpsi |
ASTM D882A |
| Tensile Strength MD |
200 |
20 |
kpsi |
ASTM D882A |
| Tensile Strength MD |
300 |
19 |
kpsi |
ASTM D882A |
|
|
|
THERMAL
|
| Shrinkage MD (150°C) |
48 |
1.5 |
% |
Unrestrained @ 150°C/30 min |
| Shrinkage MD (150°C) |
92 |
1.5 |
% |
Unrestrained @ 150°C/30 min |
| Shrinkage MD (150°C) |
200 |
1.5 |
% |
Unrestrained @ 150°C/30 min |
| Shrinkage MD (150°C) |
300 |
1.0 |
% |
Unrestrained @ 150°C/30 min |
| Shrinkage TD (150°C) |
48 - 300 |
1.0 |
% |
Unrestrained @ 150°C/30 min |
|
|
DuPont Teijin Films U.S. Limited Partnership
3600 Discovery Drive
P.O. Box 411
Hopewell, VA 23860 USA
Tel: (800) 635-4639
Fax: (804) 530-9867
|
Note: These values are typical performance data for DuPont Teijin Films' polyester film; they are not intended to be used as design data. We believe this information is the best currently available on the subject. It is offered as a possible helpful suggestion in experimentation you may care to undertake along these lines. It is subject to revision as additional knowledge and experience is gained. DuPont Teijin Films makes no guarantee of results and assumes no obligation or liability whatsoever in connection with this information. This publication is not a license to operate under, or intended to suggest infringement of, any existing patents.
CAUTION: Do not use in medical applications involving permanent implantation in the human body (DuPont Teijin Films Medical Policy). For other medical applications, see the Medical Caution Statement. DuPont Teijin Films accepts no liability for use of it's products in medical applications not reviewed and approved by DuPont Teijin Films or for product misuse. DuPont Teijin Films supplies products to an agreed specification and does not manufacture products designed specifically for medical end use.
Melinex®, Mylar® and Melinex® STTM are registered trademarks of DuPont Teijin Films U.S. Limited Partnership.
Teijin® and Tetoron® are registered trademarks of Teijin Limited used under license by DuPont Teijin Films U.S. Limited Partnership.
Teonex® is a registered trademark of Teijin DuPont Films Japan Limited and is used under license by DuPont Teijin Films U.S. Limited Partnership.
|
|
Show Printable Version